目录1bB嘉泰姆

1.产品概述                       2.产品特点1bB嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 1bB嘉泰姆
5.产品封装图                     6.电路原理图                   1bB嘉泰姆
7.功能概述                        8.相关产品1bB嘉泰姆

一,产品概述(General Description)        1bB嘉泰姆

      The CXSD61038 are high-efficiency, high frequency synchronous step-down1bB嘉泰姆
DC-DC regulator ICs capable of delivering up to 1.5A output currents. TheCXSD61038 can operate over a wide input voltage range from 2.3V to 5.5V and1bB嘉泰姆
integrate main switch and synchronous switch with very low RDS(ON) to minimize1bB嘉泰姆
the conduction loss.It is ideal for powering portable equipment that runs from a1bB嘉泰姆
single cell Lithium-Ion (Li+) battery. The output voltage can be regulated as low as1bB嘉泰姆
0.6V. The CXSD61038 can also run at 100% duty cycle for low dropout operation,1bB嘉泰姆
extending battery life in portable system.This device offers two operation modes,1bB嘉泰姆
PWM control and PFM Mode switchingcontrol, which allows a high efficiency over1bB嘉泰姆
the wider range of the load.1bB嘉泰姆
      The CXSD61038 is offered in a low profile (1mm)5-pin, thin SOT package, and1bB嘉泰姆
is available in an adjustable version.1bB嘉泰姆
二.产品特点(Features)1bB嘉泰姆

1.)CXSD61038A 1.2A output current1bB嘉泰姆
2.)CXSD61038B 1.5A output current1bB嘉泰姆
3.)High Efficiency: Up to 96%1bB嘉泰姆
4.)1.5MHz Constant Frequency Operation1bB嘉泰姆
5.)No Schottky Diode Required1bB嘉泰姆
6.)2.3V to 5.5V Input Voltage Range1bB嘉泰姆
7.) Output Voltage as Low as 0.6V1bB嘉泰姆
8.)100% Duty Cycle in Dropout1bB嘉泰姆
9.) Low Quiescent Current: 35μA1bB嘉泰姆
10.)Slope Compensated Current Mode Control for Excellent Line1bB嘉泰姆
      and Load Transient Response1bB嘉泰姆
11.)Short Circuit Protection1bB嘉泰姆
12.) Thermal Fault Protection1bB嘉泰姆
13.) Inrush Current Limit and Soft Start1bB嘉泰姆
14.)<1μA Shutdown Current1bB嘉泰姆
15.) Tiny SOT23-5 Package1bB嘉泰姆
三,应用范围 (Applications)1bB嘉泰姆

Cellular and Smart Phones1bB嘉泰姆
Wireless and DSL Modems1bB嘉泰姆
PDA1bB嘉泰姆
Digital Still and Video Cameras1bB嘉泰姆
MP3 Players1bB嘉泰姆
四.下载产品资料PDF文档 1bB嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！1bB嘉泰姆

 1bB嘉泰姆

五,产品封装图 (Package)1bB嘉泰姆
1bB嘉泰姆

六.电路原理图1bB嘉泰姆
1bB嘉泰姆

七,功能概述1bB嘉泰姆

FUNCTIONAL DESCRIPTION1bB嘉泰姆

CXSD61038 is a synchronous buck regulator IC that integrates the PWM/PFM control, top1bB嘉泰姆
and bottom switches on the same die to minimize the switching transition loss and1bB嘉泰姆
conduction loss. With ultra low RDS(ON) power switches and proprietary PWM control,1bB嘉泰姆
this regulator IC can achieve the highest efficiency and the highest switch frequency1bB嘉泰姆
simultaneously to minimize the external inductor and capacitor size, and thus1bB嘉泰姆
achieving the minimum solution footprint.The CXSD61038 requires only three external1bB嘉泰姆
power components (Cin, Cout and L). Theadjustable version can be programmed1bB嘉泰姆
with external feedback to any voltage,ranging from 0.6V to the input voltage.1bB嘉泰姆
At dropout, the converter duty cycle increases to 100% and the output voltage1bB嘉泰姆
tracks the input voltage minus the Rdson drop of the high-side MOSFET.1bB嘉泰姆
The internal error amplifier and compensation provides excellent transient response, load,1bB嘉泰姆
and line regulation. Soft start function prevents input inrush current and output1bB嘉泰姆
overshoot during start up.1bB嘉泰姆
Inductor Selection1bB嘉泰姆
For most designs, the CXSD61038 operates with inductors of 1μH to 4.7μH. Low inductance1bB嘉泰姆
values are physically smaller but require faster switching, which results in some efficiency loss.1bB嘉泰姆
The inductor value can be derived from the following equation:1bB嘉泰姆
L =VIN × ∆I L × f OSC 1bB嘉泰姆
Where ∆I L is inductor Ripple Current. Large value inductors result in lower ripple current and1bB嘉泰姆
small value inductors result in high ripple current. For optimum voltage-positioning load1bB嘉泰姆
transients, choose an inductor with DC series resistance in the 50mΩ to 150mΩ range.1bB嘉泰姆
Input Capacitor Selection1bB嘉泰姆
With the maximum load current at 1.5A, the maximum ripple current through input capacitor1bB嘉泰姆
is about 0.6Arms. A typical X7R or better grade ceramic capacitor with 6V rating and greater1bB嘉泰姆
than 10uF capacitance can handle this ripple current well. To minimize the potential noise1bB嘉泰姆
problem, place this ceramic capacitor really close to the IN and1bB嘉泰姆
GND pins. Care should be taken to minimizethe loop area formed by CIN, and IN/GND pins. 1bB嘉泰姆
Output Capacitor Selection 1bB嘉泰姆
The output capacitor is required to keep the output voltage ripple small and to ensure1bB嘉泰姆
regulation loop stability. The output capacitor must have low impedance at the switching1bB嘉泰姆
frequency. Ceramic capacitors with X5R or X7R dielectrics are recommended due to their low1bB嘉泰姆
ESR and high ripple current ratings. The outputripple VOUT is determined by:1bB嘉泰姆
VOUT × (V IN − VOUT )         1  1bB嘉泰姆
V IN × f OSC × L       8 × f osc × C31bB嘉泰姆
A 10μF ceramic can satisfy most applications.PC Board Layout Checklist When laying out the printed1bB嘉泰姆
circuit board, the following checking should be used to ensure proper operation of the CXSD61038. Check the1bB嘉泰姆
following in your layout:1bB嘉泰姆
1. The power traces, consisting of the GND trace, the SW trace and the VIN traceshould be kept short,1bB嘉泰姆
    direct and wide.1bB嘉泰姆
2. Does the (+) plates of Cin connect to Vin as closely as possible? This capacitor provides the AC current1bB嘉泰姆
    to the internal power MOSFETs.1bB嘉泰姆
3. Keep the switching node, SW, away from the sensitive VOUT node.1bB嘉泰姆
4. Keep the (-) plates of Cin and Cout as close as possible1bB嘉泰姆
八,相关产品               更多同类产品......1bB嘉泰姆

共有条评论 用户名: 密码: 验证码: 匿名发表