CXSD6276是固定的300kHz频率电压模式和同步PWM控制器两个低成本N通道mosfet设计为单电源5~12V或双电源工作电压为负载瞬变提供良好的调节

发布时间:2020-04-21 16:29:15 浏览次数:457 作者:oumao18 来源:嘉泰姆
摘要:CXSD6276 CXSD6276A集成了控制、监视和保护功能 成为一个单一的8针封装,以提供一个低成本和完美的电源解决方案。 上电复位(POR)电路监测VCC电源电压以防止 逻辑控制错误。内部0.8V参考电压提供低输出电压 低至0.8V,以便进一步应用。内置数字软启动 软启动间隔防止输出电压超调和限制 输入电流。控制器的过电流保护监视输出 通过使用低压侧MOSFET的RDS(ON)上的电压降得到的电流, 不需要电流感应电阻器
CXSD6276是固定的300kHz频率电压模式和同步PWM控制器两个低成本N通道mosfet设计为单电源5~12V或双电源工作电压为负载瞬变提供良好的调节

目录1Zu嘉泰姆

1.产品概述                       2.产品特点1Zu嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 1Zu嘉泰姆
5.产品封装图                     6.电路原理图                   1Zu嘉泰姆
7.功能概述                        8.相关产品1Zu嘉泰姆

一,产品概述(General Description)     1Zu嘉泰姆


  The CXSD6276 CXSD6276A is a fixed 300kHz frequency, voltage mode, and1Zu嘉泰姆
synchronous PWM controller. The device drives two low cost N-channel1Zu嘉泰姆
MOSFETs and is de-signed to work with single 5~12V or two supply1Zu嘉泰姆
voltage(s), providing excellent regulation for load transients.1Zu嘉泰姆
 The CXSD6276 CXSD6276A integrates controls, monitoring, and protection functions1Zu嘉泰姆
into a single 8-pin package to provide a low cost and perfect power solution.1Zu嘉泰姆
A power-on-reset (POR) circuit monitors the VCC supply voltage to prevent1Zu嘉泰姆
wrong logic controls. An internal 0.8V reference provides low output voltage1Zu嘉泰姆
down to 0.8V for further applications. An built-in digital soft-start with fixed1Zu嘉泰姆
soft-start interval prevents the output voltage from overshoot as well as limits1Zu嘉泰姆
the input current. The controller’s over-current protection monitors the output1Zu嘉泰姆
current by using the voltage drop across the low-side MOSFET’s RDS(ON),1Zu嘉泰姆
eliminating the need of a current sensing resistor. Additional under voltage and1Zu嘉泰姆
over voltage protections monitor the voltage on FB pin for short-circuit and1Zu嘉泰姆
over-voltage protections. The over-current protection cycles the soft-start1Zu嘉泰姆
function until 4 over-current events are counted.Pulling and holding the voltage1Zu嘉泰姆
on OCSET pin below 0.15V with an open drain device shuts down the controller.1Zu嘉泰姆
二.产品特点(Features)1Zu嘉泰姆


1.)Operating with Single 5~12V Supply Voltage1Zu嘉泰姆
2.)or Two Supply Voltages1Zu嘉泰姆
3.)Drive Dual Low Cost N-Channel MOSFETs1Zu嘉泰姆
     Adaptive Shoot-Through Protection1Zu嘉泰姆
4.)Built-in Feedback Compensation1Zu嘉泰姆
    Voltage-Mode PWM Control1Zu嘉泰姆
    0~100% Duty Ratio1Zu嘉泰姆
     Fast Transient Response1Zu嘉泰姆
5.)±2% 0.8V Reference1Zu嘉泰姆
    Over Line, Load Regulation, and Operating   1Zu嘉泰姆
6.)Temperature Programmable Over-Current Protection1Zu嘉泰姆
   Using RDS(ON) of Low-Side MOSFET1Zu嘉泰姆
7.)Hiccup-Mode Under-Voltage Protection1Zu嘉泰姆
8.)118% Over-Voltage Protection1Zu嘉泰姆
9.)Adjustable Output Voltage1Zu嘉泰姆
10.)Small Converter Size1Zu嘉泰姆
      300kHz Constant Switching Frequency1Zu嘉泰姆
      Small SOP-8 Package1Zu嘉泰姆
11.)Built-In Digital Soft-Start1Zu嘉泰姆
12.)Shutdown Control Using an External MOSFET1Zu嘉泰姆
13.)Lead Free and Green Devices Available1Zu嘉泰姆
三,应用范围 (Applications)1Zu嘉泰姆


Motherboard1Zu嘉泰姆
Graphics Card1Zu嘉泰姆
High Current, up to 20A, DC-DC Converters1Zu嘉泰姆
四.下载产品资料PDF文档 1Zu嘉泰姆


需要详细的PDF规格书请扫一扫微信联系我们,还可以获得免费样品以及技术支持1Zu嘉泰姆

 QQ截图20160419174301.jpg1Zu嘉泰姆

五,产品封装图 (Package)1Zu嘉泰姆

1Zu嘉泰姆

BOOT (Pin 1)1Zu嘉泰姆

This pin provides ground referenced bias voltage to the high-side MOSFET driver. A bootstrap circuit with a diode connected to 5~12V is used to create a voltage suitable to drive a logic-level N-channel MOSFET.1Zu嘉泰姆
UGATE (Pin 2)1Zu嘉泰姆
Connect this pin to the high-side N-channel MOSFET’s gate. This pin provides gate drive for the high-side MOSFET.1Zu嘉泰姆
GND (Pin 3)1Zu嘉泰姆
The GND terminal provides return path for the IC’s biascurrent and the low-side MOSFET driver’s pull-low current. Connect the pin to the system ground via very low impedance layout on PCBs.1Zu嘉泰姆
LGATE (Pin 4)1Zu嘉泰姆
Connect this pin to the low-side N-channel MOSFET’s gate. This pin provides gate drive for the low-side MOSFET. 1Zu嘉泰姆
VCC (Pin 5)1Zu嘉泰姆
Connect this pin to a 5~12V supply voltage. This pin provides bias supply for the control circuitry and the low-side MOSFET driver. The voltage at this pin is monitored for the Power-On-Reset (POR) purpose. 1Zu嘉泰姆
FB (Pin 6)1Zu嘉泰姆
This pin is the inverting input of the internal Gm amplifier.Connect this pin to the output (VOUT) of the converter via an external resistor divider for closed-loop operation.The output voltage set by the resistor divider is deter-mined using the following formula :1Zu嘉泰姆
where R1 is the resistor connected from VOUT to FB ,and R2 is the resistor connected from FB to GND. The FB pin is also monitored for under and over-voltage events. 1Zu嘉泰姆
OCSET (Pin 7)1Zu嘉泰姆
The OCSET is a dual-function input pin for over-current protection and shutdown control. Connect a resistor (ROCSET) from this pin to the Drain of the low-side MOSFET. This resistor, an internal 40μA current source (IOCSET), and the MOSFET’s on-resistance(RDSON) set the converter over-current trip level (IPEAK) according to the following formula:1Zu嘉泰姆
Pulling and holding this pin below 0.15V with an open drain device, with very low parasitic capacitor, shuts down the IC with floating output and also resets the over-current counter. Releasing OCSET pin initiates a new soft-start and the converter works again.1Zu嘉泰姆
PHASE (Pin 8) 1Zu嘉泰姆
The pin provides return path for the high-side MOSFETdriver’s pull-low current. Connect this pin to the high-side MOSFET’s source1Zu嘉泰姆
六.电路原理图1Zu嘉泰姆
blob.png1Zu嘉泰姆
七,功能概述1Zu嘉泰姆
Power-On-Reset (POR) 1Zu嘉泰姆
The CXSD6276 monitors the VCC voltage (V CC) for Power-On-Reset function, preventing wrong logic operation during powering on. When the VCC voltage is ready, the CXSD6276 starts a start-up process and then ramps the output voltage up to the target voltage. 1Zu嘉泰姆
Soft-Start1Zu嘉泰姆
The CXSD6276 has a built-in digital soft-start to control the output voltage rise and limit the current surge at the start-up. During the soft-start, an internal ramp con-nected to the one of the positive inputs of the Gm amplifier rises up from 0V to 2V to replace the reference voltage (0.8V) until the ramp voltage reaches the refer-1Zu嘉泰姆
ence voltage. The soft-start interval is about 3.2mstypical, independent of the converter’s input and out-put voltages.1Zu嘉泰姆
Over-Current Protection (OCP)1Zu嘉泰姆
The over-current function protects the switching c o nverter against over-current or short-circuit conditions. The controller senses the inductor current by detecting the drain-to-source voltage, product of the inductor’s current and the on-resistance, of the low-side MOSFET during it’s on-state. This method enhances the converter’s efficiency and reduces cost by eliminating a current sensing resistor.A resistor (ROCSET), connected from the OCSET to the1Zu嘉泰姆
Over-Current Protection (OCP) (Cont.)1Zu嘉泰姆
low-side MOSFET’s drain, programs the over-current trip level. An internal 40μA (typical) current source flowing through the ROCSET develops a voltage (VROCSET) across the ROCSET. When the VOCSET 1Zu嘉泰姆

八,相关产品                更多同类产品...... 1Zu嘉泰姆


Switching Regulator >   Buck Controller1Zu嘉泰姆

Part_No 1Zu嘉泰姆

Package 1Zu嘉泰姆

Archi1Zu嘉泰姆

tectu1Zu嘉泰姆

Phase1Zu嘉泰姆

No.of1Zu嘉泰姆

PWM1Zu嘉泰姆

Output1Zu嘉泰姆

Output 1Zu嘉泰姆

Current1Zu嘉泰姆

(A) 1Zu嘉泰姆

Input1Zu嘉泰姆

Voltage (V) 1Zu嘉泰姆

Reference1Zu嘉泰姆

Voltage1Zu嘉泰姆

(V) 1Zu嘉泰姆

Bias 1Zu嘉泰姆

Voltage1Zu嘉泰姆

(V) 1Zu嘉泰姆

Quiescent1Zu嘉泰姆

Current1Zu嘉泰姆

(uA) 1Zu嘉泰姆

min1Zu嘉泰姆

max1Zu嘉泰姆

CXSD62731Zu嘉泰姆

SOP-141Zu嘉泰姆

QSOP-161Zu嘉泰姆

QFN4x4-161Zu嘉泰姆

VM    1Zu嘉泰姆

1   1Zu嘉泰姆

1     1Zu嘉泰姆

301Zu嘉泰姆

2.9    1Zu嘉泰姆

13.21Zu嘉泰姆

0.91Zu嘉泰姆

12     1Zu嘉泰姆

80001Zu嘉泰姆

CXSD62741Zu嘉泰姆

SOP-81Zu嘉泰姆

VM   1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

201Zu嘉泰姆

2.9  1Zu嘉泰姆

13.2 1Zu嘉泰姆

0.81Zu嘉泰姆

121Zu嘉泰姆

50001Zu嘉泰姆

CXSD6274C1Zu嘉泰姆

SOP-81Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

201Zu嘉泰姆

2.91Zu嘉泰姆

13.21Zu嘉泰姆

0.81Zu嘉泰姆

121Zu嘉泰姆

50001Zu嘉泰姆

CXSD62751Zu嘉泰姆

QFN4x4-241Zu嘉泰姆

VM1Zu嘉泰姆

21Zu嘉泰姆

11Zu嘉泰姆

601Zu嘉泰姆

3.11Zu嘉泰姆

13.21Zu嘉泰姆

0.61Zu嘉泰姆

121Zu嘉泰姆

50001Zu嘉泰姆

CXSD62761Zu嘉泰姆

SOP-81Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

201Zu嘉泰姆

2.21Zu嘉泰姆

13.21Zu嘉泰姆

0.81Zu嘉泰姆

5~121Zu嘉泰姆

21001Zu嘉泰姆

CXSD6276A1Zu嘉泰姆

SOP-81Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

201Zu嘉泰姆

2.21Zu嘉泰姆

13.21Zu嘉泰姆

0.81Zu嘉泰姆

5~121Zu嘉泰姆

21001Zu嘉泰姆

CXSD6277/A/B1Zu嘉泰姆

SOP8|TSSOP81Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

51Zu嘉泰姆

51Zu嘉泰姆

13.21Zu嘉泰姆

1.25|0.81Zu嘉泰姆

5~121Zu嘉泰姆

30001Zu嘉泰姆

CXSD62781Zu嘉泰姆

SOP-81Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

101Zu嘉泰姆

3.31Zu嘉泰姆

5.51Zu嘉泰姆

0.81Zu嘉泰姆

51Zu嘉泰姆

21001Zu嘉泰姆

CXSD6279B1Zu嘉泰姆

SOP-141Zu嘉泰姆

VM   1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

101Zu嘉泰姆

51Zu嘉泰姆

13.21Zu嘉泰姆

0.81Zu嘉泰姆

121Zu嘉泰姆

20001Zu嘉泰姆

CXSD62801Zu嘉泰姆

TSSOP-241Zu嘉泰姆

|QFN5x5-321Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

21Zu嘉泰姆

201Zu嘉泰姆

51Zu嘉泰姆

13.21Zu嘉泰姆

0.61Zu嘉泰姆

5~121Zu嘉泰姆

40001Zu嘉泰姆

CXSD6281N1Zu嘉泰姆

SOP141Zu嘉泰姆

QSOP161Zu嘉泰姆

QFN-161Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

301Zu嘉泰姆

2.91Zu嘉泰姆

13.21Zu嘉泰姆

0.91Zu嘉泰姆

121Zu嘉泰姆

40001Zu嘉泰姆

CXSD62821Zu嘉泰姆

SOP-141Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

301Zu嘉泰姆

2.21Zu嘉泰姆

13.21Zu嘉泰姆

0.61Zu嘉泰姆

121Zu嘉泰姆

50001Zu嘉泰姆

CXSD6282A1Zu嘉泰姆

SOP-141Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

301Zu嘉泰姆

2.21Zu嘉泰姆

13.21Zu嘉泰姆

0.61Zu嘉泰姆

121Zu嘉泰姆

50001Zu嘉泰姆

CXSD62831Zu嘉泰姆

SOP-141Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

251Zu嘉泰姆

2.21Zu嘉泰姆

13.21Zu嘉泰姆

0.81Zu嘉泰姆

121Zu嘉泰姆

50001Zu嘉泰姆

CXSD6284/A1Zu嘉泰姆

LQFP7x7 481Zu嘉泰姆

TQFN7x7-481Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

61Zu嘉泰姆

0.0151Zu嘉泰姆

1.41Zu嘉泰姆

6.51Zu嘉泰姆

-1Zu嘉泰姆

51Zu嘉泰姆

18001Zu嘉泰姆

CXSD62851Zu嘉泰姆

TSSOP-24P1Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

21Zu嘉泰姆

201Zu嘉泰姆

2.971Zu嘉泰姆

5.51Zu嘉泰姆

0.81Zu嘉泰姆

5~121Zu嘉泰姆

50001Zu嘉泰姆

CXSD62861Zu嘉泰姆

SOP-141Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

101Zu嘉泰姆

51Zu嘉泰姆

13.21Zu嘉泰姆

0.81Zu嘉泰姆

121Zu嘉泰姆

30001Zu嘉泰姆

CXSD62871Zu嘉泰姆

SOP-8-P|DIP-81Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

11Zu嘉泰姆

301Zu嘉泰姆

2.91Zu嘉泰姆

13.21Zu嘉泰姆

1.21Zu嘉泰姆

121Zu嘉泰姆

30001Zu嘉泰姆

CXSD62881Zu嘉泰姆

SSOP281Zu嘉泰姆

QFN4x4-241Zu嘉泰姆

VM1Zu嘉泰姆

11Zu嘉泰姆

21Zu嘉泰姆

201Zu嘉泰姆

51Zu嘉泰姆

241Zu嘉泰姆

0.91Zu嘉泰姆

发表评论

共有条评论
用户名: 密码:
验证码: 匿名发表