CXSD6276A单电源电压5~12V两个电源电压驱动双低成本N通道mosfet自适应穿透保护内置反馈补偿 电压型PWM控制 0~100%占空比快速瞬态响应

发布时间:2020-04-21 16:28:53 浏览次数:386 作者:oumao18 来源:嘉泰姆
摘要:CXSD6276A控制器的过电流保护监视输出 通过使用低压侧MOSFET的RDS(ON)上的电压降得到的电流, 不需要电流感应电阻器。附加欠压和 过电压保护监视FB引脚上的电压是否短路和 过电压保护。过电流保护使软起动循环 起作用,直到4个过电流事件被计数。拉并保持电压 在低于0.15V的OCSET引脚上,使用开放式排水装置关闭控制器
CXSD6276A单电源电压5~12V两个电源电压驱动双低成本N通道mosfet自适应穿透保护内置反馈补偿 电压型PWM控制 0~100%占空比快速瞬态响应

目录vix嘉泰姆

1.产品概述                       2.产品特点vix嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 vix嘉泰姆
5.产品封装图                     6.电路原理图                   vix嘉泰姆
7.功能概述                        8.相关产品vix嘉泰姆

一,产品概述(General Description)     vix嘉泰姆


  The CXSD6276 CXSD6276A is a fixed 300kHz frequency, voltage mode, andvix嘉泰姆
synchronous PWM controller. The device drives two low cost N-channelvix嘉泰姆
MOSFETs and is de-signed to work with single 5~12V or two supplyvix嘉泰姆
voltage(s), providing excellent regulation for load transients.vix嘉泰姆
 The CXSD6276 CXSD6276A integrates controls, monitoring, and protection functionsvix嘉泰姆
into a single 8-pin package to provide a low cost and perfect power solution.vix嘉泰姆
A power-on-reset (POR) circuit monitors the VCC supply voltage to preventvix嘉泰姆
wrong logic controls. An internal 0.8V reference provides low output voltagevix嘉泰姆
down to 0.8V for further applications. An built-in digital soft-start with fixedvix嘉泰姆
soft-start interval prevents the output voltage from overshoot as well as limitsvix嘉泰姆
the input current. The controller’s over-current protection monitors the outputvix嘉泰姆
current by using the voltage drop across the low-side MOSFET’s RDS(ON),vix嘉泰姆
eliminating the need of a current sensing resistor. Additional under voltage andvix嘉泰姆
over voltage protections monitor the voltage on FB pin for short-circuit andvix嘉泰姆
over-voltage protections. The over-current protection cycles the soft-startvix嘉泰姆
function until 4 over-current events are counted.Pulling and holding the voltagevix嘉泰姆
on OCSET pin below 0.15V with an open drain device shuts down the controller.vix嘉泰姆
二.产品特点(Features)vix嘉泰姆


1.)Operating with Single 5~12V Supply Voltagevix嘉泰姆
2.)or Two Supply Voltagesvix嘉泰姆
3.)Drive Dual Low Cost N-Channel MOSFETsvix嘉泰姆
     Adaptive Shoot-Through Protectionvix嘉泰姆
4.)Built-in Feedback Compensationvix嘉泰姆
    Voltage-Mode PWM Controlvix嘉泰姆
    0~100% Duty Ratiovix嘉泰姆
     Fast Transient Responsevix嘉泰姆
5.)±2% 0.8V Referencevix嘉泰姆
    Over Line, Load Regulation, and Operating   vix嘉泰姆
6.)Temperature Programmable Over-Current Protectionvix嘉泰姆
   Using RDS(ON) of Low-Side MOSFETvix嘉泰姆
7.)Hiccup-Mode Under-Voltage Protectionvix嘉泰姆
8.)118% Over-Voltage Protectionvix嘉泰姆
9.)Adjustable Output Voltagevix嘉泰姆
10.)Small Converter Sizevix嘉泰姆
      300kHz Constant Switching Frequencyvix嘉泰姆
      Small SOP-8 Packagevix嘉泰姆
11.)Built-In Digital Soft-Startvix嘉泰姆
12.)Shutdown Control Using an External MOSFETvix嘉泰姆
13.)Lead Free and Green Devices Availablevix嘉泰姆
三,应用范围 (Applications)vix嘉泰姆


Motherboardvix嘉泰姆
Graphics Cardvix嘉泰姆
High Current, up to 20A, DC-DC Convertersvix嘉泰姆
四.下载产品资料PDF文档 vix嘉泰姆


需要详细的PDF规格书请扫一扫微信联系我们,还可以获得免费样品以及技术支持vix嘉泰姆

 QQ截图20160419174301.jpgvix嘉泰姆

五,产品封装图 (Package)vix嘉泰姆

vix嘉泰姆

BOOT (Pin 1)vix嘉泰姆

This pin provides ground referenced bias voltage to the high-side MOSFET driver. A bootstrap circuit with a diode connected to 5~12V is used to create a voltage suitable to drive a logic-level N-channel MOSFET.vix嘉泰姆
UGATE (Pin 2)vix嘉泰姆
Connect this pin to the high-side N-channel MOSFET’s gate. This pin provides gate drive for the high-side MOSFET.vix嘉泰姆
GND (Pin 3)vix嘉泰姆
The GND terminal provides return path for the IC’s biascurrent and the low-side MOSFET driver’s pull-low current. Connect the pin to the system ground via very low impedance layout on PCBs.vix嘉泰姆
LGATE (Pin 4)vix嘉泰姆
Connect this pin to the low-side N-channel MOSFET’s gate. This pin provides gate drive for the low-side MOSFET. vix嘉泰姆
VCC (Pin 5)vix嘉泰姆
Connect this pin to a 5~12V supply voltage. This pin provides bias supply for the control circuitry and the low-side MOSFET driver. The voltage at this pin is monitored for the Power-On-Reset (POR) purpose. vix嘉泰姆
FB (Pin 6)vix嘉泰姆
This pin is the inverting input of the internal Gm amplifier.Connect this pin to the output (VOUT) of the converter via an external resistor divider for closed-loop operation.The output voltage set by the resistor divider is deter-mined using the following formula :vix嘉泰姆
where R1 is the resistor connected from VOUT to FB ,and R2 is the resistor connected from FB to GND. The FB pin is also monitored for under and over-voltage events. vix嘉泰姆
OCSET (Pin 7)vix嘉泰姆
The OCSET is a dual-function input pin for over-current protection and shutdown control. Connect a resistor (ROCSET) from this pin to the Drain of the low-side MOSFET. This resistor, an internal 40μA current source (IOCSET), and the MOSFET’s on-resistance(RDSON) set the converter over-current trip level (IPEAK) according to the following formula:vix嘉泰姆
Pulling and holding this pin below 0.15V with an open drain device, with very low parasitic capacitor, shuts down the IC with floating output and also resets the over-current counter. Releasing OCSET pin initiates a new soft-start and the converter works again.vix嘉泰姆
PHASE (Pin 8) vix嘉泰姆
The pin provides return path for the high-side MOSFETdriver’s pull-low current. Connect this pin to the high-side MOSFET’s sourcevix嘉泰姆
六.电路原理图vix嘉泰姆
blob.pngvix嘉泰姆
七,功能概述vix嘉泰姆
Power-On-Reset (POR) vix嘉泰姆
The CXSD6276 monitors the VCC voltage (V CC) for Power-On-Reset function, preventing wrong logic operation during powering on. When the VCC voltage is ready, the CXSD6276 starts a start-up process and then ramps the output voltage up to the target voltage. vix嘉泰姆
Soft-Startvix嘉泰姆
The CXSD6276 has a built-in digital soft-start to control the output voltage rise and limit the current surge at the start-up. During the soft-start, an internal ramp con-nected to the one of the positive inputs of the Gm amplifier rises up from 0V to 2V to replace the reference voltage (0.8V) until the ramp voltage reaches the refer-vix嘉泰姆
ence voltage. The soft-start interval is about 3.2mstypical, independent of the converter’s input and out-put voltages.vix嘉泰姆
Over-Current Protection (OCP)vix嘉泰姆
The over-current function protects the switching c o nverter against over-current or short-circuit conditions. The controller senses the inductor current by detecting the drain-to-source voltage, product of the inductor’s current and the on-resistance, of the low-side MOSFET during it’s on-state. This method enhances the converter’s efficiency and reduces cost by eliminating a current sensing resistor.A resistor (ROCSET), connected from the OCSET to thevix嘉泰姆
Over-Current Protection (OCP) (Cont.)vix嘉泰姆
low-side MOSFET’s drain, programs the over-current trip level. An internal 40μA (typical) current source flowing through the ROCSET develops a voltage (VROCSET) across the ROCSET. When the VOCSET vix嘉泰姆

八,相关产品                更多同类产品...... vix嘉泰姆


Switching Regulator >   Buck Controllervix嘉泰姆

Part_No vix嘉泰姆

Package vix嘉泰姆

Archivix嘉泰姆

tectuvix嘉泰姆

Phasevix嘉泰姆

No.ofvix嘉泰姆

PWMvix嘉泰姆

Outputvix嘉泰姆

Output vix嘉泰姆

Currentvix嘉泰姆

(A) vix嘉泰姆

Inputvix嘉泰姆

Voltage (V) vix嘉泰姆

Referencevix嘉泰姆

Voltagevix嘉泰姆

(V) vix嘉泰姆

Bias vix嘉泰姆

Voltagevix嘉泰姆

(V) vix嘉泰姆

Quiescentvix嘉泰姆

Currentvix嘉泰姆

(uA) vix嘉泰姆

minvix嘉泰姆

maxvix嘉泰姆

CXSD6273vix嘉泰姆

SOP-14vix嘉泰姆

QSOP-16vix嘉泰姆

QFN4x4-16vix嘉泰姆

VM    vix嘉泰姆

1   vix嘉泰姆

1     vix嘉泰姆

30vix嘉泰姆

2.9    vix嘉泰姆

13.2vix嘉泰姆

0.9vix嘉泰姆

12     vix嘉泰姆

8000vix嘉泰姆

CXSD6274vix嘉泰姆

SOP-8vix嘉泰姆

VM   vix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

20vix嘉泰姆

2.9  vix嘉泰姆

13.2 vix嘉泰姆

0.8vix嘉泰姆

12vix嘉泰姆

5000vix嘉泰姆

CXSD6274Cvix嘉泰姆

SOP-8vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

20vix嘉泰姆

2.9vix嘉泰姆

13.2vix嘉泰姆

0.8vix嘉泰姆

12vix嘉泰姆

5000vix嘉泰姆

CXSD6275vix嘉泰姆

QFN4x4-24vix嘉泰姆

VMvix嘉泰姆

2vix嘉泰姆

1vix嘉泰姆

60vix嘉泰姆

3.1vix嘉泰姆

13.2vix嘉泰姆

0.6vix嘉泰姆

12vix嘉泰姆

5000vix嘉泰姆

CXSD6276vix嘉泰姆

SOP-8vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

20vix嘉泰姆

2.2vix嘉泰姆

13.2vix嘉泰姆

0.8vix嘉泰姆

5~12vix嘉泰姆

2100vix嘉泰姆

CXSD6276Avix嘉泰姆

SOP-8vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

20vix嘉泰姆

2.2vix嘉泰姆

13.2vix嘉泰姆

0.8vix嘉泰姆

5~12vix嘉泰姆

2100vix嘉泰姆

CXSD6277/A/Bvix嘉泰姆

SOP8|TSSOP8vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

5vix嘉泰姆

5vix嘉泰姆

13.2vix嘉泰姆

1.25|0.8vix嘉泰姆

5~12vix嘉泰姆

3000vix嘉泰姆

CXSD6278vix嘉泰姆

SOP-8vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

10vix嘉泰姆

3.3vix嘉泰姆

5.5vix嘉泰姆

0.8vix嘉泰姆

5vix嘉泰姆

2100vix嘉泰姆

CXSD6279Bvix嘉泰姆

SOP-14vix嘉泰姆

VM   vix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

10vix嘉泰姆

5vix嘉泰姆

13.2vix嘉泰姆

0.8vix嘉泰姆

12vix嘉泰姆

2000vix嘉泰姆

CXSD6280vix嘉泰姆

TSSOP-24vix嘉泰姆

|QFN5x5-32vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

2vix嘉泰姆

20vix嘉泰姆

5vix嘉泰姆

13.2vix嘉泰姆

0.6vix嘉泰姆

5~12vix嘉泰姆

4000vix嘉泰姆

CXSD6281Nvix嘉泰姆

SOP14vix嘉泰姆

QSOP16vix嘉泰姆

QFN-16vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

30vix嘉泰姆

2.9vix嘉泰姆

13.2vix嘉泰姆

0.9vix嘉泰姆

12vix嘉泰姆

4000vix嘉泰姆

CXSD6282vix嘉泰姆

SOP-14vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

30vix嘉泰姆

2.2vix嘉泰姆

13.2vix嘉泰姆

0.6vix嘉泰姆

12vix嘉泰姆

5000vix嘉泰姆

CXSD6282Avix嘉泰姆

SOP-14vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

30vix嘉泰姆

2.2vix嘉泰姆

13.2vix嘉泰姆

0.6vix嘉泰姆

12vix嘉泰姆

5000vix嘉泰姆

CXSD6283vix嘉泰姆

SOP-14vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

25vix嘉泰姆

2.2vix嘉泰姆

13.2vix嘉泰姆

0.8vix嘉泰姆

12vix嘉泰姆

5000vix嘉泰姆

CXSD6284/Avix嘉泰姆

LQFP7x7 48vix嘉泰姆

TQFN7x7-48vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

6vix嘉泰姆

0.015vix嘉泰姆

1.4vix嘉泰姆

6.5vix嘉泰姆

-vix嘉泰姆

5vix嘉泰姆

1800vix嘉泰姆

CXSD6285vix嘉泰姆

TSSOP-24Pvix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

2vix嘉泰姆

20vix嘉泰姆

2.97vix嘉泰姆

5.5vix嘉泰姆

0.8vix嘉泰姆

5~12vix嘉泰姆

5000vix嘉泰姆

CXSD6286vix嘉泰姆

SOP-14vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

10vix嘉泰姆

5vix嘉泰姆

13.2vix嘉泰姆

0.8vix嘉泰姆

12vix嘉泰姆

3000vix嘉泰姆

CXSD6287vix嘉泰姆

SOP-8-P|DIP-8vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

1vix嘉泰姆

30vix嘉泰姆

2.9vix嘉泰姆

13.2vix嘉泰姆

1.2vix嘉泰姆

12vix嘉泰姆

3000vix嘉泰姆

CXSD6288vix嘉泰姆

SSOP28vix嘉泰姆

QFN4x4-24vix嘉泰姆

VMvix嘉泰姆

1vix嘉泰姆

2vix嘉泰姆

20vix嘉泰姆

5vix嘉泰姆

24vix嘉泰姆

0.9vix嘉泰姆

发表评论

共有条评论
用户名: 密码:
验证码: 匿名发表