CXSD6276A单电源电压5~12V两个电源电压驱动双低成本N通道mosfet自适应穿透保护内置反馈补偿 电压型PWM控制 0~100%占空比快速瞬态响应

发布时间:2020-04-21 16:28:53 浏览次数:368 作者:oumao18 来源:嘉泰姆
摘要:CXSD6276A控制器的过电流保护监视输出 通过使用低压侧MOSFET的RDS(ON)上的电压降得到的电流, 不需要电流感应电阻器。附加欠压和 过电压保护监视FB引脚上的电压是否短路和 过电压保护。过电流保护使软起动循环 起作用,直到4个过电流事件被计数。拉并保持电压 在低于0.15V的OCSET引脚上,使用开放式排水装置关闭控制器
CXSD6276A单电源电压5~12V两个电源电压驱动双低成本N通道mosfet自适应穿透保护内置反馈补偿 电压型PWM控制 0~100%占空比快速瞬态响应

目录N1a嘉泰姆

1.产品概述                       2.产品特点N1a嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 N1a嘉泰姆
5.产品封装图                     6.电路原理图                   N1a嘉泰姆
7.功能概述                        8.相关产品N1a嘉泰姆

一,产品概述(General Description)     N1a嘉泰姆


  The CXSD6276 CXSD6276A is a fixed 300kHz frequency, voltage mode, andN1a嘉泰姆
synchronous PWM controller. The device drives two low cost N-channelN1a嘉泰姆
MOSFETs and is de-signed to work with single 5~12V or two supplyN1a嘉泰姆
voltage(s), providing excellent regulation for load transients.N1a嘉泰姆
 The CXSD6276 CXSD6276A integrates controls, monitoring, and protection functionsN1a嘉泰姆
into a single 8-pin package to provide a low cost and perfect power solution.N1a嘉泰姆
A power-on-reset (POR) circuit monitors the VCC supply voltage to preventN1a嘉泰姆
wrong logic controls. An internal 0.8V reference provides low output voltageN1a嘉泰姆
down to 0.8V for further applications. An built-in digital soft-start with fixedN1a嘉泰姆
soft-start interval prevents the output voltage from overshoot as well as limitsN1a嘉泰姆
the input current. The controller’s over-current protection monitors the outputN1a嘉泰姆
current by using the voltage drop across the low-side MOSFET’s RDS(ON),N1a嘉泰姆
eliminating the need of a current sensing resistor. Additional under voltage andN1a嘉泰姆
over voltage protections monitor the voltage on FB pin for short-circuit andN1a嘉泰姆
over-voltage protections. The over-current protection cycles the soft-startN1a嘉泰姆
function until 4 over-current events are counted.Pulling and holding the voltageN1a嘉泰姆
on OCSET pin below 0.15V with an open drain device shuts down the controller.N1a嘉泰姆
二.产品特点(Features)N1a嘉泰姆


1.)Operating with Single 5~12V Supply VoltageN1a嘉泰姆
2.)or Two Supply VoltagesN1a嘉泰姆
3.)Drive Dual Low Cost N-Channel MOSFETsN1a嘉泰姆
     Adaptive Shoot-Through ProtectionN1a嘉泰姆
4.)Built-in Feedback CompensationN1a嘉泰姆
    Voltage-Mode PWM ControlN1a嘉泰姆
    0~100% Duty RatioN1a嘉泰姆
     Fast Transient ResponseN1a嘉泰姆
5.)±2% 0.8V ReferenceN1a嘉泰姆
    Over Line, Load Regulation, and Operating   N1a嘉泰姆
6.)Temperature Programmable Over-Current ProtectionN1a嘉泰姆
   Using RDS(ON) of Low-Side MOSFETN1a嘉泰姆
7.)Hiccup-Mode Under-Voltage ProtectionN1a嘉泰姆
8.)118% Over-Voltage ProtectionN1a嘉泰姆
9.)Adjustable Output VoltageN1a嘉泰姆
10.)Small Converter SizeN1a嘉泰姆
      300kHz Constant Switching FrequencyN1a嘉泰姆
      Small SOP-8 PackageN1a嘉泰姆
11.)Built-In Digital Soft-StartN1a嘉泰姆
12.)Shutdown Control Using an External MOSFETN1a嘉泰姆
13.)Lead Free and Green Devices AvailableN1a嘉泰姆
三,应用范围 (Applications)N1a嘉泰姆


MotherboardN1a嘉泰姆
Graphics CardN1a嘉泰姆
High Current, up to 20A, DC-DC ConvertersN1a嘉泰姆
四.下载产品资料PDF文档 N1a嘉泰姆


需要详细的PDF规格书请扫一扫微信联系我们,还可以获得免费样品以及技术支持N1a嘉泰姆

 QQ截图20160419174301.jpgN1a嘉泰姆

五,产品封装图 (Package)N1a嘉泰姆

N1a嘉泰姆

BOOT (Pin 1)N1a嘉泰姆

This pin provides ground referenced bias voltage to the high-side MOSFET driver. A bootstrap circuit with a diode connected to 5~12V is used to create a voltage suitable to drive a logic-level N-channel MOSFET.N1a嘉泰姆
UGATE (Pin 2)N1a嘉泰姆
Connect this pin to the high-side N-channel MOSFET’s gate. This pin provides gate drive for the high-side MOSFET.N1a嘉泰姆
GND (Pin 3)N1a嘉泰姆
The GND terminal provides return path for the IC’s biascurrent and the low-side MOSFET driver’s pull-low current. Connect the pin to the system ground via very low impedance layout on PCBs.N1a嘉泰姆
LGATE (Pin 4)N1a嘉泰姆
Connect this pin to the low-side N-channel MOSFET’s gate. This pin provides gate drive for the low-side MOSFET. N1a嘉泰姆
VCC (Pin 5)N1a嘉泰姆
Connect this pin to a 5~12V supply voltage. This pin provides bias supply for the control circuitry and the low-side MOSFET driver. The voltage at this pin is monitored for the Power-On-Reset (POR) purpose. N1a嘉泰姆
FB (Pin 6)N1a嘉泰姆
This pin is the inverting input of the internal Gm amplifier.Connect this pin to the output (VOUT) of the converter via an external resistor divider for closed-loop operation.The output voltage set by the resistor divider is deter-mined using the following formula :N1a嘉泰姆
where R1 is the resistor connected from VOUT to FB ,and R2 is the resistor connected from FB to GND. The FB pin is also monitored for under and over-voltage events. N1a嘉泰姆
OCSET (Pin 7)N1a嘉泰姆
The OCSET is a dual-function input pin for over-current protection and shutdown control. Connect a resistor (ROCSET) from this pin to the Drain of the low-side MOSFET. This resistor, an internal 40μA current source (IOCSET), and the MOSFET’s on-resistance(RDSON) set the converter over-current trip level (IPEAK) according to the following formula:N1a嘉泰姆
Pulling and holding this pin below 0.15V with an open drain device, with very low parasitic capacitor, shuts down the IC with floating output and also resets the over-current counter. Releasing OCSET pin initiates a new soft-start and the converter works again.N1a嘉泰姆
PHASE (Pin 8) N1a嘉泰姆
The pin provides return path for the high-side MOSFETdriver’s pull-low current. Connect this pin to the high-side MOSFET’s sourceN1a嘉泰姆
六.电路原理图N1a嘉泰姆
blob.pngN1a嘉泰姆
七,功能概述N1a嘉泰姆
Power-On-Reset (POR) N1a嘉泰姆
The CXSD6276 monitors the VCC voltage (V CC) for Power-On-Reset function, preventing wrong logic operation during powering on. When the VCC voltage is ready, the CXSD6276 starts a start-up process and then ramps the output voltage up to the target voltage. N1a嘉泰姆
Soft-StartN1a嘉泰姆
The CXSD6276 has a built-in digital soft-start to control the output voltage rise and limit the current surge at the start-up. During the soft-start, an internal ramp con-nected to the one of the positive inputs of the Gm amplifier rises up from 0V to 2V to replace the reference voltage (0.8V) until the ramp voltage reaches the refer-N1a嘉泰姆
ence voltage. The soft-start interval is about 3.2mstypical, independent of the converter’s input and out-put voltages.N1a嘉泰姆
Over-Current Protection (OCP)N1a嘉泰姆
The over-current function protects the switching c o nverter against over-current or short-circuit conditions. The controller senses the inductor current by detecting the drain-to-source voltage, product of the inductor’s current and the on-resistance, of the low-side MOSFET during it’s on-state. This method enhances the converter’s efficiency and reduces cost by eliminating a current sensing resistor.A resistor (ROCSET), connected from the OCSET to theN1a嘉泰姆
Over-Current Protection (OCP) (Cont.)N1a嘉泰姆
low-side MOSFET’s drain, programs the over-current trip level. An internal 40μA (typical) current source flowing through the ROCSET develops a voltage (VROCSET) across the ROCSET. When the VOCSET N1a嘉泰姆

八,相关产品                更多同类产品...... N1a嘉泰姆


Switching Regulator >   Buck ControllerN1a嘉泰姆

Part_No N1a嘉泰姆

Package N1a嘉泰姆

ArchiN1a嘉泰姆

tectuN1a嘉泰姆

PhaseN1a嘉泰姆

No.ofN1a嘉泰姆

PWMN1a嘉泰姆

OutputN1a嘉泰姆

Output N1a嘉泰姆

CurrentN1a嘉泰姆

(A) N1a嘉泰姆

InputN1a嘉泰姆

Voltage (V) N1a嘉泰姆

ReferenceN1a嘉泰姆

VoltageN1a嘉泰姆

(V) N1a嘉泰姆

Bias N1a嘉泰姆

VoltageN1a嘉泰姆

(V) N1a嘉泰姆

QuiescentN1a嘉泰姆

CurrentN1a嘉泰姆

(uA) N1a嘉泰姆

minN1a嘉泰姆

maxN1a嘉泰姆

CXSD6273N1a嘉泰姆

SOP-14N1a嘉泰姆

QSOP-16N1a嘉泰姆

QFN4x4-16N1a嘉泰姆

VM    N1a嘉泰姆

1   N1a嘉泰姆

1     N1a嘉泰姆

30N1a嘉泰姆

2.9    N1a嘉泰姆

13.2N1a嘉泰姆

0.9N1a嘉泰姆

12     N1a嘉泰姆

8000N1a嘉泰姆

CXSD6274N1a嘉泰姆

SOP-8N1a嘉泰姆

VM   N1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

20N1a嘉泰姆

2.9  N1a嘉泰姆

13.2 N1a嘉泰姆

0.8N1a嘉泰姆

12N1a嘉泰姆

5000N1a嘉泰姆

CXSD6274CN1a嘉泰姆

SOP-8N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

20N1a嘉泰姆

2.9N1a嘉泰姆

13.2N1a嘉泰姆

0.8N1a嘉泰姆

12N1a嘉泰姆

5000N1a嘉泰姆

CXSD6275N1a嘉泰姆

QFN4x4-24N1a嘉泰姆

VMN1a嘉泰姆

2N1a嘉泰姆

1N1a嘉泰姆

60N1a嘉泰姆

3.1N1a嘉泰姆

13.2N1a嘉泰姆

0.6N1a嘉泰姆

12N1a嘉泰姆

5000N1a嘉泰姆

CXSD6276N1a嘉泰姆

SOP-8N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

20N1a嘉泰姆

2.2N1a嘉泰姆

13.2N1a嘉泰姆

0.8N1a嘉泰姆

5~12N1a嘉泰姆

2100N1a嘉泰姆

CXSD6276AN1a嘉泰姆

SOP-8N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

20N1a嘉泰姆

2.2N1a嘉泰姆

13.2N1a嘉泰姆

0.8N1a嘉泰姆

5~12N1a嘉泰姆

2100N1a嘉泰姆

CXSD6277/A/BN1a嘉泰姆

SOP8|TSSOP8N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

5N1a嘉泰姆

5N1a嘉泰姆

13.2N1a嘉泰姆

1.25|0.8N1a嘉泰姆

5~12N1a嘉泰姆

3000N1a嘉泰姆

CXSD6278N1a嘉泰姆

SOP-8N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

10N1a嘉泰姆

3.3N1a嘉泰姆

5.5N1a嘉泰姆

0.8N1a嘉泰姆

5N1a嘉泰姆

2100N1a嘉泰姆

CXSD6279BN1a嘉泰姆

SOP-14N1a嘉泰姆

VM   N1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

10N1a嘉泰姆

5N1a嘉泰姆

13.2N1a嘉泰姆

0.8N1a嘉泰姆

12N1a嘉泰姆

2000N1a嘉泰姆

CXSD6280N1a嘉泰姆

TSSOP-24N1a嘉泰姆

|QFN5x5-32N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

2N1a嘉泰姆

20N1a嘉泰姆

5N1a嘉泰姆

13.2N1a嘉泰姆

0.6N1a嘉泰姆

5~12N1a嘉泰姆

4000N1a嘉泰姆

CXSD6281NN1a嘉泰姆

SOP14N1a嘉泰姆

QSOP16N1a嘉泰姆

QFN-16N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

30N1a嘉泰姆

2.9N1a嘉泰姆

13.2N1a嘉泰姆

0.9N1a嘉泰姆

12N1a嘉泰姆

4000N1a嘉泰姆

CXSD6282N1a嘉泰姆

SOP-14N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

30N1a嘉泰姆

2.2N1a嘉泰姆

13.2N1a嘉泰姆

0.6N1a嘉泰姆

12N1a嘉泰姆

5000N1a嘉泰姆

CXSD6282AN1a嘉泰姆

SOP-14N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

30N1a嘉泰姆

2.2N1a嘉泰姆

13.2N1a嘉泰姆

0.6N1a嘉泰姆

12N1a嘉泰姆

5000N1a嘉泰姆

CXSD6283N1a嘉泰姆

SOP-14N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

25N1a嘉泰姆

2.2N1a嘉泰姆

13.2N1a嘉泰姆

0.8N1a嘉泰姆

12N1a嘉泰姆

5000N1a嘉泰姆

CXSD6284/AN1a嘉泰姆

LQFP7x7 48N1a嘉泰姆

TQFN7x7-48N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

6N1a嘉泰姆

0.015N1a嘉泰姆

1.4N1a嘉泰姆

6.5N1a嘉泰姆

-N1a嘉泰姆

5N1a嘉泰姆

1800N1a嘉泰姆

CXSD6285N1a嘉泰姆

TSSOP-24PN1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

2N1a嘉泰姆

20N1a嘉泰姆

2.97N1a嘉泰姆

5.5N1a嘉泰姆

0.8N1a嘉泰姆

5~12N1a嘉泰姆

5000N1a嘉泰姆

CXSD6286N1a嘉泰姆

SOP-14N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

10N1a嘉泰姆

5N1a嘉泰姆

13.2N1a嘉泰姆

0.8N1a嘉泰姆

12N1a嘉泰姆

3000N1a嘉泰姆

CXSD6287N1a嘉泰姆

SOP-8-P|DIP-8N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

1N1a嘉泰姆

30N1a嘉泰姆

2.9N1a嘉泰姆

13.2N1a嘉泰姆

1.2N1a嘉泰姆

12N1a嘉泰姆

3000N1a嘉泰姆

CXSD6288N1a嘉泰姆

SSOP28N1a嘉泰姆

QFN4x4-24N1a嘉泰姆

VMN1a嘉泰姆

1N1a嘉泰姆

2N1a嘉泰姆

20N1a嘉泰姆

5N1a嘉泰姆

24N1a嘉泰姆

0.9N1a嘉泰姆

发表评论

共有条评论
用户名: 密码:
验证码: 匿名发表