CXLD64008 are highly accurate, low noise, LDO Voltage Regulators that are capable of providing an output current that is in excess of 1A with a maximum dropout voltage of 1.3V at 1A

目录ZUt嘉泰姆

1.产品概述                       2.产品特点
3.应用范围                       4.下载产品资料PDF文档 
5.产品封装图</span>                     6.电路原理图</span>                   
7.功能概述                        8.相关产品ZUt嘉泰姆

一,产品概述(General Description)         ZUt嘉泰姆

   The CXLD64008 series are highly accurate, low noise,LDO Voltage Regulators that are capable of providing an output current that is in excess of 1A with a maximum dropout voltage of 1.3V at 1A （ CXLD64008A33） .This series contains four fixed output voltages of 1.2V, 1.8V, 2.5V and 3.3V that have no minimum load requirement to maintain regulation.On chip trimming adjusts the reference/output voltage to within ±2% accuracy.Internal protection features consist of output current limiting, safe operating area compensation,and thermal shutdown. ZUt嘉泰姆

  The CXLD64008series can operate with up to 18V input. Devices are available in SOT223.ZUt嘉泰姆

二.产品特点(Features)ZUt嘉泰姆

Output Current in Excess of 1A
1.)Dropout Voltage:80mV@ IOUT =100mA
（CXLD64008A33）</span>
2.)Operating Voltage Range: 2.5V～18V
3.)Highly Accuracy: ±2％</span>
4.)Adjustable Output Voltage Option
5.)Standby Current: 52uA（TYP.）</span>
6.)High Ripple Rejection: 70dB@1KHz（CXLD64008A33）</span>
7.)Line Regulation: 2mV（TYP.）</span>
8.)Temperature Stability≤0.5%
9.)Thermal Shutdown Protection：160℃</span>
10.)Packages:SOT223 ,SOT89-3,TO252-2L，SOT23-3
三,应用范围 (Applications)ZUt嘉泰姆

Consumer and Industrial Equipment Point of
Regulation
Switching Power Supply Post Regulation
Hard Drive Controllers
Battery Chargers
四.下载产品资料PDF文档 ZUt嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持</span>！</span>ZUt嘉泰姆

五,产品封装图 (Package)ZUt嘉泰姆

六.电路原理图</span>ZUt嘉泰姆

七,功能概述ZUt嘉泰姆

Applications Information
1. Input Bypass Capacitor
An input capacitor is recommended. A 10uF tantalum on the input is a suitable input bypassing for almost all applications.
2. Output Capacitor
The output capacitor is critical in maintaining regulator stability, and must meet the required conditions for both minimum amount of capacitance and ESR (Equivalent Series Resistance).The minimum output capacitance required by the CXLD64008 is 10μF,if a tantalum capacitor is used. Any increase of the output capacitance will merely improve the loop stability and transient response. The ESR of the output capacitor should be less than 0.5Ω .
3. Load Regulation
The CXLD64008 regulates the voltage that appears between its output and ground pins, or between its output and adjust pins. In some cases, line resistances can introduce errors to the voltage across the load. To obtain the best load regulation, a few precautions are needed. Figure1, shows a typical application using a fixed output regulator. The Rt1 and Rt2 are the line resistances. It is obvious that the VLOAD is less than the VOUT by the sum of
the voltage drops along the line resistances. In this case, the load regulation seen at the RLOAD would be degraded from the datasheet specification. To improve this , the load should be tied directly to the output terminal on the positive side and directly tied to the ground terminal on the negative side.
八,相关产品                更多同类产品......ZUt嘉泰姆

ZUt嘉泰姆