CXSD61022A wide input voltage, high efficiency CC step-down DC/DC converter that operates in either

CXSD61022A wide input voltage, high efficiency CC step-down DC/DC converter that operates in either CV (Constant Output Voltage) mode or CC (Constant Output Current) mode

目录

1.产品概述                       2.产品特点
3.应用范围                       4.产品封装图
5.电路原理图                   6.产品PCB                   
7.产品BOM                      8.产品PDF文档 
9.功能概述                      10.相关产品

 

一,产品概述(General Description)     

---

    CXSD61022A is a wide input voltage, high efficiency CC step-down DC/DC converter that operates in either CV (Constant Output Voltage) mode or CC (Constant Output Current) mode. CXSD61022A provides up to 2.5A output current at 125kHz switching frequency.
      CXSD61022A provides OVP pin for output over voltage protection.Protection features include cycle-by-cycle current limit,thermal shutdown, and frequency foldback at short circuit. The devices are available in a SOP-8EP package and require very few external devices for operation.
二.产品特点(Features)

---

42V Input Voltage Surge
40V Steady State Operation
Up to 2.5A output current
Output Voltage 2.5V to 10V
Resistor Programmable

− Current Limit from 1A to 2.5A
− Cable Compensation from 0Ω to 0.4Ω

±7.5% CC Accuracy
− Compensation of Input /Output Voltage Change
− Temperature Compensation
2% Feedback Voltage Accuracy
Up to 94% Efficiency
125kHz Switching Frequency Eases EMI Design
Advanced Feature Set
− Integrated Soft Start
− Thermal Shutdown
− Protection Against Shorted ISET Pin
Patented E-LTI technology improves
transient response.
SOP-8EP Package
三,应用范围 (Applications)

---

 Car Charger/ Adaptor
Rechargeable Portable Devices
General-Purpose CC/CV Supply
四,产品封装图 (Package)

Pin No.	NAME	Description
1	HSB	High Side Bias Pin. This provides power to the internal high-side MOSFET gate driver.Connect a 100nF capacitor from HSB pin to SW pin.
2	IN	Power Supply Input. Bypass this pin with a 10μF ceramic capacitor to GND, placed as close to the IC as possible.
3	SW	Power Switching Output to External Inductor.
4	GND	Ground. Connect this pin to a large PCB copper area for best heat dissipation. Return FB,COMP, and ISET to this GND, and connect this GND to power GND at a single point for best noise immunity.
5	FB	Feedback Input. The voltage at this pin is regulated to 0.800V. Connect to the resistor divider between output and GND to set the output voltage.
6	LCOMP	Output cable resistance compensation.
7	OVP/EN	CXSD61022A: OVP input. If the voltage at this pin exceeds 1.25V, the IC shuts down high-side switch.CXSD61022B: EN input. If the voltage at this pin is below 1.5V, the IC remains shut-off.
8	ISET	Output Current Setting Pin. Connect a resistor from ISET to GND to program the out putcurrent.
	Exposed Pad	Heat Dissipation Pad. Connect this exposed pad to large ground copper area with copper and vias.

五,电路原理图

六, 产品PCB

七.产品BOM  
  (略)
八.产品PDF文档 

---

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！

 

九,功能概述

---

CV/CC Loop Regulation
As seen in Functional Block Diagram, the CXSD61022A is
a Constant On Time (COT) mode pulse width
modulation (PWM) converter with CC and CV control.
The converter operates as follows:
The main loop of CXSD61022A uses a COT mode control
which provides a very fast transient response with no
external component and no need loop compensation.
The CXSD61022A also adopt a proprietary circuit that
ensures enable use very low ESR capacitor to maintain
loop stability.
turns on. The high side MOSFET is turn off after
internal one shot timer expires. This one shot time is
set by VIN and VOUT to maintain a constant frequency.
The one shot timer is reset and high side MOSFET
turns on again when feedback voltage falls below the
reference voltage. An internal ramp is generating to
simulate output ripple, eliminating the need for ESR
induced output ripple from COT control mode. When
high side MOSFET turns off, the SW node of the
inductor swings to a diode voltage below ground,
causing the inductor current to decrease and magnetic
energy to be transferred to output. This state continues
until the next cycle start again
十,相关产品                  更多同类产品......

---

DC-DC降压IC
型号	输入耐压	输出电压	输出电流	反馈电压	工作频率	效率	静态工作电流
CXSD61023A	42V	可调输出/带CC/cv模式 恒流模式保护	3.5A	0.8V	125K	94%	3mA
CXSD61021A	42V	可调输出/带CC/cv模式 恒流模式保护	3A	0.8V	125K	94%	3mA
CXSD61022A	42V	可调输出/带CC/cv模式 恒流模式保护	2.5A	0.8V	125K	94%	3mA
CXSD61020	40V	可调输出/带CC/cv模式	3A	0.8V	225K	92%	2.84mA
CXSD61027	50V	5V固定输出	3.2A		150K	87%	4.7mA
CXSD61026	50V	5V固定输出	2.4A		150K	89%	4.7mA
CXSD61025	50V	5V固定输出	2.1A		150K	90%	4.7mA
CXSD61024	50V	5V固定输出	1.8A		150K	90%	4.7mA
CXSD61015	40V	可调输出/带CC/CV模式带线损补偿	3A	0.8V	125K	94%	4mA
CXSD61014A	40V	5V固定输出	3.5A		150K	93%	2mA
CXSD61013B	45V	可调输出/	2A	1.23V	150K	93%	2mA
CXSD61012	40V	可调输出/带CC/CV模式	2A	1.18V	110K	93%	10mA
CXSD61011	42V	可调输出	3A	0.8V	50-500K	91%	3mA
CXSD61018	40V	可调输出/带CC/cv模式	3A	1.25V	180K	89%	2.1mA
CXSD61019	40V	可调输出/带CC/cv模式	3.5A	1.25V	180K	87%	2.1mA
CXSD61017	45V	可调输出/带CC模式	3A	1.25V	150K	89%	2.0mA
CXSD61016	45V	可调输出/带CC模式	2A	1.235V	150K	83%	2.0mA
CXSD61006B	4.75V-40V	可调输出	0.8A	0.8V	550K	90%	10uA
CXSD61006	4.0-42V	可调输出	1.5A	0.8V	650K	91%	600uA
CXSD61005	4.5-25V	可调输出	1.8A	0.8V	1.4M	92%	1.8mA
CXSD61010A	20V	可调输出	3.5A	1.2V	400K	89%	700uA
CXSD61010	28V	可调输出	3A	1.22V	380K	89%	3mA
CXSD61009	20V	可调输出	3A	0.8V	380K	88%	3mA
CXSD61008	20V	可调输出	2A	0.8V	380K	89%	2mA
CXSD61007	45V	5.0V/可调输出/3.3/12V	2A	1.23V	150K	82%	2mA
CXSD61003	45V	5.0V/可调输出	3A	1.23V	380K	73%	2mA
CXSD61004	27V	可调输出	2A	1.22V	420K	95%	1mA