The JTMA7158 has two synchronous buck PWM control-lers with(3)

Short Circuit Protection (Cont.)
increased, and continue to regulate up until the MOSFETs is damaged. The resistance of the short should include
wiring, PCB traces, contact resistances, and all of the return paths.
The higher duty cycle will give a higher COMP voltage level, and it is easy to touch the trip point. The compensa-
tion components also affect the response of COMP voltage; smaller caps may give a faster response.
The output current has faster rising time during short;the COMP pin will have a sharp rise. However, if the cur-
rent rises too fast, it may cause a false trip. The output capacitance and its ESR can affect the rising time of the
current during short.
Layout Consideration
In high power switching regulator, a correct layout is im-portant to ensure proper operation of the regulator. In
general, interconnecting impedances should be mini-mized by using short, wide printed circuit traces.
Signal and power grounds are to be kept separate and finally combined using ground plane construction or
single point grounding. Figure 10 illustrates the layout,with bold lines indicating high current paths; these traces
must be short and wide. Components along the bold lines should be placed lose together. Below is a check-
list for your layout :

The metal plate of the bottom of the packages (SOP-20) must be soldered to the PCB and connected to the

GND plane on the backside through several thermal vias.upper MOSFET; the output capacitor should be near the
loads. The input capacitor GND should be close to the output capacitor GND and the lower MOSFET GND.
· The drain of the MOSFETs (VIN and phase nodes) should be a large plane for heat sinking.

The input capacitor should be near the drain of the Keep the switching nodes (UGATE, LGATE and PHASE)

away from sensitive small signal nodes since these nodes are fast moving signals. Therefore, keep traces to
these nodes as short as possible.The traces from the gate drivers to the MOSFETs

(UGATE1, LGATE1, UGATE2, LGATE2) should be short and wide.
· Decoupling capacitor, compensation component, the resistor dividers, boot capacitors, and SS capacitors
should be close their pins.

八,相关产品

Part_No	Package & Pins	Topology	Architecture	Phase	No. of PWM Outputs	Output Current (max)(A)	Input Voltage (V)		Reference Voltage(V)	Bias Voltage (typ) (V)	Quiescent Current (typ)(uA)
Part_No	Package & Pins	Topology	Architecture	Phase	No. of PWM Outputs	Output Current (max)(A)	min	max	Reference Voltage(V)	Bias Voltage (typ) (V)	Quiescent Current (typ)(uA)
JTMA7068	SOP-14	Buck	VM	1	1	30	2.9	13.2	0.9	12	8000
	QSOP-16
	QFN4x4-16
JTMA7065	SOP-8	Buck	VM	1	1	20	2.9	13.2	0.8	12	5000
JTMA7065C	SOP-8	Buck	VM	1	1	20	2.9	13.2	0.8	12	5000
JTMA7098	QFN4x4-24	Multiphase	VM	2	1	60	3.1	13.2	0.6	12	5000
JTMA7120	SOP-8	Buck	VM	1	1	20	2.2	13.2	0.8	5月12日	2100
JTMA7120A	SOP-8	Buck	VM	1	1	20	2.2	13.2	0.8	5月12日	2100
JTMA7037/A/B	SOP-8	Buck	VM	1	1	5	5	13.2	1.25 / 0.8	5月12日	3000
JTMA7037/A/B	TSSOP-8	Buck	VM	1	1	5	5	13.2	1.25 / 0.8	5月12日	3000
JTMA7057	SOP-8	Buck	VM	1	1	10	3.3	5.5	0.8	5	2100
JTMA7062B	SOP-14	Buck	VM	1	1	10	5	13.2	0.8	12	2000
JTMA7066	TSSOP-24	Buck	VM	1	2	20	5	13.2	0.6	5月12日	4000
JTMA7066	QFN5x5-32	Buck	VM	1	2	20	5	13.2	0.6	5月12日	4000
JTMA7067N	SOP-14	Buck	VM	1	1	30	2.9	13.2	0.9	12	4000
	QSOP-16
	QFN-16
JTMA7073	SOP-14	Buck	VM	1	1	30	2.2	13.2	0.6	12	5000
JTMA7073A	SOP-14	Buck	VM	1	1	30	2.2	13.2	0.6	12	5000
JTMA7074	SOP-14	Buck	VM	1	1	25	2.2	13.2	0.8	12	5000
JTMA7095/A	LQFP7x7-48	Buck	VM	1	6	0.015	1.4	6.5	-	5	1800
	TQFN7x7-48	Boost
		Flyback
JTMA7116	TSSOP-24P	Buck	VM	1	2	20	2.97	5.5	0.8	5月12日	5000
JTMA7063	SOP-14	Buck	VM	1	1	10	5	13.2	0.8	12	3000
JTMA7064	SOP-8-P	Buck	VM	1	1	30	2.9	13.2	1.2	12	3000
JTMA7064	DIP-8	Buck	VM	1	1	30	2.9	13.2	1.2	12	3000
JTMA7108	SSOP-28	Buck	VM	1	2	20	5	24	0.9	5	1200
JTMA7108	QFN4x4-24	Buck	VM	1	2	20	5	24	0.9	5	1200
JTMA7158	SOP-20	Buck	VM	1	2	20	2.2	13.2	0.6	5月12日	4000
JTMA7181	SOP-8		VM	1	2	-	-	-	-	5月12日	550
JTMA7181	DFN3x3-10		VM	1	2	-	-	-	-	5月12日	550
JTMA38HC/42/3/4/5A	DIP-8	Buck	VM	1	1	1	1.2	9	24	5	9 ~ 24
	SOP-8	Boost
		Flyback
		Forward
JTMA7138	SSOP-16	Buck	VM	1	1	25	3	25	0.6	5	1700
	QFN4x4-16
	TQFN3x3-16
JTMA7199	TDFN3x3-10	Buck	COT	1	1	25	3	25	0.5	5	350
JTMA8700	QFN4x4-24	Buck	CM	2	1	40	4.5	13.2	0.6	5月12日	4000
JTMA8720B	SOP8-P	Buck	VM	1	1	20	3	13.2	0.8	5月12日	2500
JTMA8720B	TDFN3x3-10	Buck	VM	1	1	20	3	13.2	0.8	5月12日	2500
JTMA8722A/B/C/D	SOP8-P	Buck	VM	1	1	25	3	13.2	0.6 /0.8	5月12日	1200
JTMA8723	TDFN3x3-10	Buck	VM	1	1	25	4	13.2	0.8	5月12日	2000
JTMA8724	TDFN3x3-10	Buck	COT	1	1	25	4.5	25	0.6	5月12日	80
JTMA8725/A	SOP-8P	Buck	VM	1	1	25	4.5	13.2	0.8	5月12日	16000
JTMA8726	TQFN3x3-10	Buck	VM	1	1	25	4.5	13.2	0.6	5月12日	2500
JTMA8727/L	TDFN3x3-10	Buck	COT	1	1	30	3	25	0.8	5月12日	2000
JTMA8728	TQFN3x3-16	Buck	COT	1	1	30	1.8	28	0.6	5	600
JTMA8732	QFN4x4-24	Buck	VM	2	1	50	4.5	13.2	0.6	5月12日	5000
JTMA8811	TQFN4x4-24	Buck	COT	1	2	15	6	25	2	N	550
JTMA8812	TQFN4x4-24	Buck	COT	1	2	15	6	25	2	N	550
JTMA8813/A	TQFN4x4-24	Buck	COT	1	2	20	3	28	0.75	5	800
JTMA8813/A	TQFN3x3-20	Buck	COT	1	2	20	3	28	0.75	5	800
JTMA8814	TQFN3x3-16	Buck	COT	1	1	20	1.8	28	0.75	5	400
JTMA8815	QFN3.5x3.5-14	Buck	COT	1	1	20	1.8	28	0.75	5	400
JTMA8815	TQFN3x3-16	Buck	COT	1	1	20	1.8	28	0.75	5	400
JTMA8816	TQFN3x3-16	Buck	COT	1	2	20	1.8	28	0.75	5	400
JTMA8819	QFN3x3-20	Buck	COT	1	2	20	3	28	1.8 /1.5 /0.5	5	740
JTMA8819	TQFN3x3-16	Buck	COT	1	2	20	3	28	1.8 /1.5 /0.5	5	740
JTMA8820	TQFN4x4-24	Buck	CM	1	2	15	5	28	0.5	N	3000
JTMA8820	QFN3x3-20	Buck	CM	1	2	15	5	28	0.5	N	3000
JTMA8821	TDFN3x3-10	Buck	COT	1	1	20	1.8	28	0.5	5	250
JTMA8822/C	TQFN3x3-20	Buck	COT	1	2	15	6	25	2	N	550
JTMA8823A/B	TQFN3x3-20	Buck	COT	1	2	15	5.5	25	0.6	N	50
JTMA8868	TQFN3x3-20	Buck	COT	1	2	20	3	28	0.75	5	180
JTMA7088	QFN4x4-24	Multiphase	VM	2	1	60	3.1	13.2	0.85	12	5000
JTMA7165A/B/C	SOP-8P	Buck	VM	1	1	20	2.9	13.2	0.8	12	16000
JTMA7159A	SOP-20	Buck	VM	2	2	30	10	13.2	1	12	5000
JTMA8828	TDFN3x3-10	Buck	COT	1	1	25	1.8	28	0.7	5	250
JTMA8728	TQFN 3x3 16	Buck	COT	1	1	30	1.8	28	0.6	5	600

(责任编辑：oumao18)